JERRY Portable Sawmill vs Woodland Mills HM126MAX: Bed Length, Head Rig and Trailer
Short answer: both mills are published for logs up to 26 in (66 cm), so log diameter does not separate them. They differ in bed length (3.1 m standard on the Woodland Mills HM126MAX against a 4 m track and 3.5 m cutting length on the JERRY portable line), head rig (4-post carriage with an auto-locking sawhead against a linear guide rail with double sliding blocks), and trailer package (torsion axle against leaf springs with a winch and ramp).
The HM126 name now points to the HM126MAX
Woodland Mills sells the HM126 platform today as the HM126MAX, and that is the specification sheet used for this comparison. The change that matters for buyers is on the sawhead: the published maximum cut width is now 26 in (66 cm), the same number as the log diameter, where a mill that accepts a 26 in log often cuts a narrower board than the log it starts with. Within the same Woodland Mills lineup the SE126 still pairs a 26 in log diameter with a 24 in cut width, which is a useful reminder that the two figures are separate settings on any bandsaw mill.
Everything below is taken from figures the two manufacturers publish themselves, in November 2026. Where a number is not published, the table says so instead of filling the gap with an estimate, and nothing here replaces a quotation for the exact configuration you are buying.
Published specification comparison
| Specification | JERRY portable sawmill (JR59 – JR1000) | Woodland Mills HM126MAX |
|---|---|---|
| Max. log diameter | 600 / 700 / 920 / 1050 mm (24 / 28 / 36 / 41 in) | 26 in (66 cm) |
| Max. width of cut | Not published in the model table; confirmed per order | 26 in (66 cm) |
| Max. board thickness | Not published in the model table; confirmed per order | 7 in (18 cm) |
| Standard cutting length | 3.5 m (11 ft 6 in) of log, on a 4 m track | 10 ft 5 in (3.1 m) of log |
| Track width | Not published in the model table | 30-1/2 in (77.5 cm) |
| Track extension | Track built to order in sections; length confirmed per order | 6 ft 5 in (1.95 m) or 2 ft 6 in (0.76 m) sections |
| Head rig | Linear guide rail with double sliding blocks; guide clearance down to 0.02 mm | 4-post carriage with reinforced back beam and welded tubular crossbeam |
| Head lift | Electric auto lift; reducer with locking at any position; chain drive with bearing-mounted sprocket | Auto-locking sawhead, 16 positions, acme lead screw, adjustment to 1/64 in |
| Blade guide | Roller blade guide; adjustable log supports | Auto-locking adjustable blade guide with stainless steel V-rollers |
| Carriage wheels | Not published | Dual-race bearing wheels with stainless wire track sweepers |
| Saw wheel diameter | 400 mm (JR59, JR69) or 500 mm (JR80, JR1000) | 19 in (48 cm) cast iron |
| Blade size | 3300 × 35 × 0.9 mm or 4200 × 35 × 0.9 mm | 1.25 in × 144 in × 0.042 in (32 × 3660 × 1.0 mm) |
| Published kerf | Not published | 0.080 in (2 mm) |
| Blade engagement | Motor / engine drive, auto travel and auto lift | Centrifugal clutch (throttle-engaged) |
| Published cutting speed | 6 m/min (JR59, JR69); 4 m/min (JR80, JR1000) | Not published |
| Power unit | 5.5 kW / 18 HP (JR59, JR69); 7.5 kW / 18 HP (JR80); 11 kW / 27 HP (JR1000) | 14 HP Kohler, manual or electric start |
| Power options | Electric, gasoline or diesel; 220 V / 380 V | Gasoline |
| Machine weight | 500 kg (JR59, JR69); 650 kg (JR80); 770 kg (JR1000) | 797 lb (362 kg) ground mounted; 1327 lb (602 kg) on the Woodlander trailer |
| Levelling | Adjustable support legs, two per metre of track | 12 levelling feet (ground); 4 jacks on the Woodlander, 6 on the Woodlander XL |
| Log holding | Adjustable log supports; track anti-derailment stops | 1× Quick Lock clamp, 2 short and 2 long log supports |
| Surface protection | Powder coat on non-wearing surfaces, hot-dip galvanized on contact surfaces | Powder coat paint with galvanized steel components |
| Published list price | Quoted per configuration, MOQ 1 set; model prices are listed on each product page | US$4,395 ground mounted; US$6,340 with Woodlander trailer (list price, subject to change) |
Woodland Mills HM126MAX figures as published by the Woodland Mills official site (woodlandmills.com), November 2026. JERRY figures as published on the JR-series product page of forest-machinery.com, November 2026. List prices are subject to change.
Bed length: 3.1 m standard against a 4 m track
The most quoted difference in this class is bed length, and it is worth doing the arithmetic rather than reading the headline. Woodland Mills publishes a standard cutting length of 10 ft 5 in (3.1 m) for the HM126MAX, made up of two 6 ft 5 in track sections. Adding one 6 ft 5 in section takes the published capacity to 16 ft 11 in (5.16 m), and the trailer version is offered with either length at the point of order.
The JERRY portable table lists a 4 m track with a maximum log cutting length of 3.5 m, which leaves half a metre of head travel at each end of the log. That is a longer single-piece bed than the 3.1 m standard, and it is the reason a buyer cutting 12 ft poles can do it without ordering an extension. Beyond 3.5 m the track is built to order in additional sections, and the length is confirmed with the quotation rather than taken from a catalogue.
Two practical notes. First, a longer bed is also a longer frame to level: the JERRY track carries two adjustable support legs per metre for that reason, and the HM126MAX ships with 12 levelling feet. Second, bed length sets the longest log, not the widest board; the width question is answered by cut width and board thickness.
Head rig: two ways to keep a saw head on line
Woodland Mills builds the HM126MAX head as a 4-post carriage, reinforced with a back beam and a welded tubular crossbeam, and anchors it between laser-cut side plates. Movement is on dual-race bearing wheels that run on square-topped rails, with stainless wire sweepers clearing sawdust from the track. Head height is set through an auto-locking mechanism with 16 positions on an acme lead screw, published as accurate to 1/64 in, and the blade guide is an auto-locking adjustable unit using stainless V-rollers on a machined aluminium arm.
JERRY's portable head runs on a linear guide rail with double sliding blocks, with guide clearance down to 0.02 mm, which is roughly half the thickness of a human hair. Lift is electric and automatic, through a reducer that locks at any position, and the lifting chain runs on a bearing-mounted sprocket. The published factory record for the lift is 30,000 raise-and-lower cycles without a fault. Blade guidance is by roller guide, and the track carries anti-derailment stops at the ends.
The difference a buyer feels in use is where the adjustment happens. A 16-position locking sawhead gives the operator repeatable board thickness without counting turns; a motorised lift with a locking reducer removes the cranking from the same task. Both are published, verifiable approaches, and neither one is a substitute for a level bed.
Trailer: torsion axle against leaf springs plus a winch
Woodland Mills sells the trailer as the Woodlander package: a galvanised steel frame tied into the sawmill track to form a box structure, an independent torsion axle, 5.30-12 DOT-approved tyres, a full LED light kit, a 2 in (50 mm) ball coupler, four levelling jacks on the standard Woodlander and six on the XL, and a head locking kit for transport. The trailer-mounted HM126MAX is published at 1327 lb (602 kg) complete. Woodland Mills states that the package is sold as an off-road unit, with the road components provided to help register it as a home-built trailer locally, so the registration question belongs to your jurisdiction, not to the spec sheet. A log loading ramp and winch kit is listed as an optional accessory.
JERRY's trailer version uses leaf springs to isolate the frame from road vibration, a heavy towing bracket with an adjustable coupler, highway tyres with fenders, and four heavy-duty adjustable support legs that double as levelling on soft ground. A winch and a loading ramp are part of the trailer package rather than an extra, and a hydraulic log lifter rated to 8 t is available for logs that are too heavy to drag up a ramp.
On the road, the two packages answer different questions: torsion axle and DOT tyres are aimed at towing behaviour, leaf springs and a winch are aimed at getting a heavy log onto the bed at the landing. If your logs arrive by forwarder at the roadside, price the loading method before you compare axles.
Power and market access
The HM126MAX is published with a single power family: a 14 HP Kohler four-cycle engine, available with manual or electric start, with a cast iron cylinder bore, overhead valve layout, a four-stage air filtration system and a centrifugal clutch. Woodland Mills backs the engine with a three-year commercial warranty and the mill with a three-year warranty that excludes wearing parts and cosmetic damage.
JERRY's portable line is published with three power families across four models: electric motors from 5.5 kW to 11 kW at 220 V or 380 V, gasoline engines, and diesel engines. That matters where the site has no reliable single-phase supply, or where a buyer wants to run the mill from a generator. Gasoline versions can be supplied with EPA and EU Stage V documentation, diesel versions with Stage V, and every machine leaves with CE documentation from a factory audited by TÜV Rheinland. Terms are FOB, CFR, CIF or EXW from Qingdao, with an MOQ of one set.
Compliance paperwork is usually the item that decides an import, so compare the document pack rather than the badge: ask each supplier for the declaration of conformity, the engine emission certificate and the test report for the exact unit you are buying, and check that the serial numbers match. The Incoterm you choose also changes what is included, which is set out in this comparison of FOB, CFR, CIF and EXW for forestry machinery.
Which mill fits which job
| Buying situation | What the published numbers suggest |
|---|---|
| Homestead cutting up to 3 m logs, one operator, petrol power | HM126MAX ground mount: 3.1 m standard bed, 26 in log and cut width, 362 kg, 12 levelling feet, 3-year warranty |
| Cutting 12 ft poles without an extension | JERRY 4 m track with 3.5 m cutting length covers the length in one bed |
| Site with no reliable single-phase supply | JERRY electric 220 V / 380 V, gasoline or diesel; HM126MAX is published as gasoline only |
| Milling wide live-edge slabs | HM126MAX publishes 26 in cut width matching its 26 in log diameter; confirm JERRY's cut width for the quoted model |
| Towing between sites on public roads | Woodlander: torsion axle, DOT tyres, LED kit, 2 in ball, sold as off-road with road parts for local registration |
| Heavy logs at the landing, one operator | JERRY trailer package includes winch and ramp, with an optional 8 t hydraulic log lifter |
What is not published
Three gaps are worth stating plainly, because they are the numbers buyers ask for and neither page answers them. Woodland Mills does not publish a feed rate, a blade tensioning method or a maximum log weight for the HM126MAX. JERRY does not publish a single cut width or maximum board thickness in the JR-series model table, because the frame and head are specified per order. Neither page states a CE or EPA status for the exact unit, so compliance should be confirmed from the certificate rather than from a web page.
Questions buyers ask before choosing
Is the Woodland Mills HM126 still sold?
Woodland Mills lists the HM126 platform today as the HM126MAX, and the figures in this article come from that product page in November 2026. If you are comparing against an older HM126 specification found elsewhere, check the cut width: the HM126MAX is published at 26 in (66 cm) of cut width against a 26 in log diameter.
How long a log can each mill cut as standard?
The HM126MAX is published at 10 ft 5 in (3.1 m) standard, extended by 6 ft 5 in sections to 16 ft 11 in. The JERRY portable line is published with a 4 m track and a maximum log cutting length of 3.5 m, with longer beds built to order.
Does the HM126MAX have hydraulic log loading?
No hydraulic loading is published for it. Loading and turning are manual, with one Quick Lock clamp and four log supports, and a log loading ramp and winch kit is listed as an optional accessory. The JERRY trailer package includes a winch and ramp, with an 8 t hydraulic log lifter available as an option.
Can a JERRY portable sawmill run on diesel or on site power?
Yes. The JR-series is published with electric motors at 220 V or 380 V, gasoline engines and diesel engines across the four models, with motor power from 5.5 kW to 11 kW depending on the model. State the voltage and plug type when ordering.
Which head lift is easier to live with?
Both are published as repeatable. The HM126MAX uses a 16-position auto-locking sawhead on an acme lead screw, accurate to 1/64 in, and the JERRY head lifts electrically through a locking reducer, so the operator does not crank between cuts. Try both if you can; the difference is in the operator's shoulder, not the spec sheet.
Key facts
HM126MAX: 26 in (66 cm) log diameter and 26 in cut width, 7 in board thickness, 3.1 m standard cutting length, 797 lb (362 kg) ground mounted, US$4,395 list.
HM126MAX with Woodlander trailer: 1327 lb (602 kg), torsion axle, 5.30-12 DOT tyres, LED lights, 2 in ball, 4 jacks, US$6,340 list.
JERRY portable line: 600 / 700 / 920 / 1050 mm log diameter, 3.5 m cutting length on a 4 m track, 500 to 770 kg, electric 220 V / 380 V, gasoline or diesel.
JERRY head: linear guide rail with double sliding blocks, guide clearance down to 0.02 mm, electric lift through a locking reducer, 30,000 published lift cycles without a fault.
JERRY build: powder coat on non-wearing surfaces, hot-dip galvanized contact surfaces, two adjustable support legs per metre of track, track anti-derailment stops.
JERRY trade terms: CE documentation, TÜV Rheinland factory audit, Verified Custom Manufacturer, MOQ 1 set, FOB / CFR / CIF / EXW from Qingdao.
Read the rest of the portable sawmill comparison series
The same product line has been compared against the Woodland Mills HM130MAX, the Wood-Mizer LT15 and the Norwood LumberMan MN27. For the class decision above these models, see portable against commercial sawmills, and for the coating question see galvanized contact surfaces in wet climates.
Woodland Mills, HM126, HM126MAX, FULLCUT, RapidChange and Woodlander are trademarks of their respective owner. This article compares published specifications and does not imply any affiliation.
Next step
Send the longest log you expect to cut, the widest board you sell, your power supply and your destination port, and we will quote a JR-series configuration against those numbers rather than a catalogue page.
Email: jerry@jerry-sawmill.com
Site: forest-machinery.com



